When you would install a new item, you should not forget the steps as to how it will be placed. You should follow them so you can correctly install any Profile Design Cobra bars. This has been required on the policies of its warranty which will be given to the buyer. If you have no knowledge on this, you can ask for help from a dealer nearby.
There is a manual that contains the methods on how it should be done. When you have decided to do it yourself, you have to prepare the tools that you would be using for it. You should have Allen wrenches or torque wrenches. You should also have sandpaper as it would be used in making it smooth. When you have prepared all of it, you can now start with it.
You should avoid greasing the clamping area. If you would be greasing it, it would only cause the bar to slip from it. You have to make sure that such situation would not happen especially when you are already using your bike. It would cause you to lose control while you are riding the bike. It would be very dangerous on your part if that would happen.
You have to make sure that the diameter of the bar clamp would match to the diameter of its stem. This should be checked so that you could avoid any problems with it. It would not fit if their diameter would not be the same. Before you would buy, you have to check the diameter so you would not waste your money on buying one.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You should slide the lever to the bar. If it makes you uncomfortable, you should adjust it depending on what you want. You have to place it carefully. You have to remember that if it would be broken, it would affect the warranty of the material.
You could wrap it if you want to. If you would try it, you have to make sure that you are wearing your helmet. Check if it would be working properly before you would be using it on far away places.
Following the right procedures is really necessary. That would be dangerous for somebody if he will be losing control of his bike. Major injuries might be acquired from it.
There is a manual that contains the methods on how it should be done. When you have decided to do it yourself, you have to prepare the tools that you would be using for it. You should have Allen wrenches or torque wrenches. You should also have sandpaper as it would be used in making it smooth. When you have prepared all of it, you can now start with it.
You should avoid greasing the clamping area. If you would be greasing it, it would only cause the bar to slip from it. You have to make sure that such situation would not happen especially when you are already using your bike. It would cause you to lose control while you are riding the bike. It would be very dangerous on your part if that would happen.
You have to make sure that the diameter of the bar clamp would match to the diameter of its stem. This should be checked so that you could avoid any problems with it. It would not fit if their diameter would not be the same. Before you would buy, you have to check the diameter so you would not waste your money on buying one.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You should slide the lever to the bar. If it makes you uncomfortable, you should adjust it depending on what you want. You have to place it carefully. You have to remember that if it would be broken, it would affect the warranty of the material.
You could wrap it if you want to. If you would try it, you have to make sure that you are wearing your helmet. Check if it would be working properly before you would be using it on far away places.
Following the right procedures is really necessary. That would be dangerous for somebody if he will be losing control of his bike. Major injuries might be acquired from it.
About the Author:
When you are looking for information about Profile Design Cobra Bars go to the web pages online here today. You can see details at http://www.sportfactoryproshop.com now.
Aucun commentaire:
Enregistrer un commentaire